The allowable clearance reduction shall be based on one of the methods specified in Table 308.4.2. Where required clearances are not listed in Table 308.4.2, the reduced clearances shall be determined by linear interpolation between the distances listed in the table. Reduced clearances shall not be derived by extrapolation below the range of the table. **TABLE 308.4.2 CLEARANCE REDUCTION METHODS^{a, b, c}**

TYPE OF PROTECTIVE ASSEMBLY^b	REDUCED CLEARANCE WITH PROTECTION (inches)^b
	Horizontal Combustible Assemblies Located Above the Heat Source				Horizontal Combustible Assemblies Located Beneath the Heat Source and All Vertical Combustible Assemblies
	Required clearance to combustibles without protection (inches)^b				Required clearance to combustibles without protection (inches)
	36	18	9	6	36	18	9	6
Galvanized sheet steel, having a minimum thickness of 0.0236 inch (No. 24 gage), mounted on 1-inch glass fiber or mineral wool batt reinforced with wire on the back, 1 inch off the combustible assembly	18	9	5	3	12	6	3	3
Galvanized sheet steel, having a minimum thickness of 0.0236 inch (No. 24 gage), spaced 1 inch off the combustible assembly	18	9	5	3	12	6	3	2
Two layers of galvanized sheet steel, having a minimum thickness of 0.0236 inch (No. 24 gage), having a 1-inch airspace between layers, spaced 1 inch off the combustible assembly	18	9	5	3	12	6	3	3
Two layers of galvanized sheet steel, having a minimum thickness of 0.0236 inch (No. 24 gage), having 1 inch of fiberglass insulation between layers, spaced 1 inch off the combustible assembly	18	9	5	3	12	6	3	3
0.5-inch inorganic insulating board, over 1 inch of fiberglass or mineral wool batt, against the combustible assembly	24	12	6	4	18	9	5	3
3 1/2-inch brick wall, spaced 1 inch off the combustible wall	—	—	—	—	12	6	6	6
3 1/2-inch brick wall, against the combustible wall	—	—	—	—	24	12	6	5

For SI: 1 inch = 25.4 mm, °C = [(°F) – 32]/1.8, 1 pound per cubic foot = 16.02 kg/m³, 1.0 Btu × in/(ft²× h × °F) = 0.144 W/m²× K. a. Reduction of clearances from combustible materials shall not interfere with combustion air, draft hood clearance and relief, and access for servicing. b. Mineral wool and glass fiber batts (blanket or board) shall have a minimum density of 8 pounds per cubic foot and a minimum melting point of 1,500°F. Insulation material utilized as part of a clearance reduction system shall have a thermal conductivity of 1.0 Btu × in/(ft²× h × °F) or less. Insulation board shall be formed of noncombustible material. c. For limitations on clearance reduction for solid fuel-burning appliances, masonry chimneys, connector pass-throughs, masonry fireplaces and kitchen ducts, see Sections 308.4.2.1 through 308.4.2.5. ##### 308.4.2.1 Solid fuel-burning appliances. The clearance reduction methods specified in Table 308.4.2 shall not be utilized to reduce the clearance required for solid fuel-burning appliances that are labeled for installation with clearances of 12 inches (305 mm) or less. Where appliances are labeled for installation with clearances of greater than 12 inches (305 mm), the clearance reduction methods of Table 308.4.2 shall not reduce the clearance to less than 12 inches (305 mm). ##### 308.4.2.2 Masonry chimneys. The clearance reduction methods specified in Table 308.4.2 shall not be utilized to reduce the clearances required for masonry chimneys as specified in Chapter 8 and the *International Building Code*. ##### 308.4.2.3 Chimney connector pass-throughs. The clearance reduction methods specified in Table 308.4.2 shall not be utilized to reduce the clearances required for chimney connector pass-throughs as specified in Section 803.10.4. ##### 308.4.2.4 Masonry fireplaces. The clearance reduction methods specified in Table 308.4.2 shall not be utilized to reduce the clearances required for masonry fireplaces as specified in Chapter 8 and the *International Building Code*. ##### 308.4.2.5 Kitchen exhaust ducts. The clearance reduction methods specified in Table 308.4.2 shall not be utilized to reduce the minimum clearances required by Section 506.3.11.1 for kitchen exhaust ducts enclosed in a shaft.

Chapter 3·General Regulations

Each length of pipe and tubing and each pipe fitting utilized in a mechanical system is required to bear which of the following markings?

Plastic pipe, fittings, and components installed as part of a building mechanical system must be third-party certified as conforming to which standard?

A fuel-fired warm-air furnace is installed at a high elevation. According to the code, what restriction applies to the fuel input rate of the appliance?

Where vibration isolation of mechanical equipment and appliances is employed, what additional provision is required by code?

In a commercial building located in a flood hazard area, mechanical equipment is installed below the required flood elevation. What condition allows this installation under the exception?

66 more questions in this chapter

Chapter 3General Regulations